en:navody
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
en:navody [2019/01/29 16:13] – [Soldering iron] fluktuacia | en:navody [2019/01/31 14:08] – [CAN] fluktuacia | ||
---|---|---|---|
Line 53: | Line 53: | ||
=== An aid for smoke extraction === | === An aid for smoke extraction === | ||
- | During any soldering, the evaporated flux creates a very unpleasant smoke that irritates the respiratory tract. One of the solutions is to build a simple aid from an older PC ventilator. Connect it to an adjustable power supply and set it on a table in a way that it would blow the some away from the soldering workplace. In order to reduce a noice, the ventilator can be put onto a piece of rubber, for example from an old inner tube of a bike. | + | During any soldering, the evaporated flux creates a very unpleasant smoke that irritates the respiratory tract. One of the solutions is to build a simple aid from an older PC ventilator. Connect it to an adjustable power supply and set it on a table in a way that it would blow the smoke away from the soldering workplace. In order to reduce a noise, the ventilator can be put onto a piece of rubber, for example from an old inner tube of a bike. |
==== Using the tools ==== | ==== Using the tools ==== | ||
Line 60: | Line 60: | ||
=== Connecting the oscilloscope probe === | === Connecting the oscilloscope probe === | ||
- | An oscilloscope’s probe ground can be easily connected to a MLAB kit thanks to the base [[en: | + | An oscilloscope’s probe ground can be easily connected to an MLAB kit thanks to the base [[en: |
The signal probe input can be connected to MLAB in a following way: the connecting cable is cut to half, part of the cable is stripped of an insulation and a crimp pin connector is crimped onto the cable. Now the cable, via the crimp pin connector, can be easily attached to the probe’s hook and its second end with the original PC terminal, can be connected to the pinch outlets of all modules. | The signal probe input can be connected to MLAB in a following way: the connecting cable is cut to half, part of the cable is stripped of an insulation and a crimp pin connector is crimped onto the cable. Now the cable, via the crimp pin connector, can be easily attached to the probe’s hook and its second end with the original PC terminal, can be connected to the pinch outlets of all modules. | ||
Line 70: | Line 70: | ||
==== Power supply ==== | ==== Power supply ==== | ||
- | Powering | + | Power provided |
=== Power supply up to +5V === | === Power supply up to +5V === | ||
Line 80: | Line 80: | ||
== 3.3V == | == 3.3V == | ||
- | Power voltage | + | Power voltage |
=== Voltage higher than +5V === | === Voltage higher than +5V === | ||
- | This category usually involves 7.2 (2x Li-ion cell) or +12V (lead-acid battery or other power supplies). For safety reasons it is therefore led via a yellow (+) and black (-) cable, following | + | This category usually involves 7.2 (2x Li-ion cell) or +12V (lead-acid battery or other power supplies). For safety reasons it is therefore led via a yellow (+) and black (-) cable, following |
{{: | {{: | ||
Line 90: | Line 90: | ||
=== Symmetrical power supply === | === Symmetrical power supply === | ||
- | This kind of power supply, conventionally +12V and -12V, is used in analogue constructions, | + | This kind of power supply, conventionally +12V and -12V, is used in analogue constructions, |
{{: | {{: | ||
Line 100: | Line 100: | ||
=== Very high voltage power supply === | === Very high voltage power supply === | ||
- | It includes power voltage in range of hundreds volts to ones of kV. Such powering is used for certain special detectors or gas discharge lamps, LASERs, etc. It is distributed via a coaxial cable with SHV or MHV connectors. | + | It includes power voltage in range of hundreds |
==== High-frequency signals ==== | ==== High-frequency signals ==== | ||
=== Asymmetrical signals === | === Asymmetrical signals === | ||
- | Analogue VF signals are distributed in MLAB via a classic VF Pigtail usually made form coax RG-174 with both ends having a screw-type SMA (Male) connector. | + | Analogue VF signals are distributed in MLAB via a classic VF Pigtail usually made from coax RG-174 with both ends having a screw-type SMA (Male) connector. |
{{: | {{: | ||
Line 123: | Line 123: | ||
==== Digital buses ==== | ==== Digital buses ==== | ||
- | Digital buses, such as I2C, TWI or 1-wire are distributed between the modules via standard cables, usually only adjusted so that one plastic ending contains all the bus’s wires, | + | Digital buses, such as I2C, TWI or 1-wire are distributed between the modules via standard cables, usually only adjusted so that one plastic ending contains all the bus’s wires, |
===== Maintenance and cleaning ===== | ===== Maintenance and cleaning ===== | ||
Line 129: | Line 129: | ||
==== Interconnecting cables ==== | ==== Interconnecting cables ==== | ||
- | Due to a gradual wear by a mechanical switching, the interconnecting cables’ connectors loose their conductivity. It last several hundreds of connections and re-connections until the phenomenon occurs, but it might be speeded up by careless transport of already connected constructions, | + | Due to a gradual wear by a mechanical switching, the interconnecting cables’ connectors loose their conductivity. It lasts several hundreds of connections and re-connections until the phenomenon occurs, but it might be speeded up by a careless transport of already connected constructions, |
- | The above-mentioned state can be repaired by | + | The above-mentioned state can be repaired by napružení kontaktu konektoru |
- | + | ||
- | U propojovacích kablíků se v důsledku jejich postupného opotřebení mechanickým přepojováním snižuje vodivost jejich konektorů. Trvá řádově několik stovek zapojení, než se tento jev projeví, ale může být urychlen například neopatrnou přepravou zapojených konstrukcí, | + | |
- | + | ||
- | Tento stav lze napravit opětovným napružením kontaktu konektoru šroubovákem, nebo jiným podobným nástrojem. To se provádí zvenku u zámku konektoru. tlakem na pružinku proti stolu. | + | |
==== Modules ==== | ==== Modules ==== | ||
- | Most of the modules | + | Most of the modules |
<WRAP info> It is not possible to use electrostatic duster for a dust removal as it might cause a destruction of certain electronic circuits in modules </ | <WRAP info> It is not possible to use electrostatic duster for a dust removal as it might cause a destruction of certain electronic circuits in modules </ | ||
Line 167: | Line 162: | ||
=== Screw terminal === | === Screw terminal === | ||
- | There are two widespread | + | There are two widespread |
The first type is more common mostly due to its low price. However, thanks to using a sheet metal washer under screws, it is not possible to fasten a naked wire of small diameter well into this type of screw terminal. Furthermore, | The first type is more common mostly due to its low price. However, thanks to using a sheet metal washer under screws, it is not possible to fasten a naked wire of small diameter well into this type of screw terminal. Furthermore, | ||
Line 179: | Line 174: | ||
=== Spring terminal block === | === Spring terminal block === | ||
- | Spring terminal block are an excellent modern substitute for screw terminals, which are slowly becoming technically obsolete. Their disadvantage, | + | Spring terminal block are an excellent modern substitute for screw terminals, which are slowly becoming technically obsolete. Their disadvantage, |
One of the commonly used spring terminal block is WAGO256. | One of the commonly used spring terminal block is WAGO256. | ||
Line 189: | Line 184: | ||
==== High-frequency signals ==== | ==== High-frequency signals ==== | ||
- | High-frequency signals are led to external devices in the same way as they are between modules - via coaxial | + | High-frequency signals are led to external devices in the same way as they are between modules - via coaxial |
In order to connect distant devices, such as receiving antenna, F-connector is a good choice, mainly thanks to its easy assembly and disassembly, | In order to connect distant devices, such as receiving antenna, F-connector is a good choice, mainly thanks to its easy assembly and disassembly, | ||
Line 196: | Line 192: | ||
=== USB === | === USB === | ||
- | The most widely | + | The most widely |
{{: | {{: | ||
- | Using an USB connector on a module requires placing a current fuse into the charing from USB (usually 750mA PTC). Otherwise a short circuit can cause a fall of HOST system and thus a data loss (of a tuned program). | + | Using a USB connector on a module requires placing a current fuse into the charing from USB (usually 750mA PTC). Otherwise a short circuit can cause a fall of HOST system and thus a data loss (of a tuned program). |
=== RS-232 === | === RS-232 === | ||
Line 208: | Line 204: | ||
=== RS-485 === | === RS-485 === | ||
- | In industry, this bus is used with terminal blocks. Therefore it is suitable | + | In industry, this bus is used with terminal blocks. Therefore it is practical |
=== CAN === | === CAN === | ||
- | To distribute CAN bus over longer | + | To distribute CAN bus over longer |
===== Test constructions ===== | ===== Test constructions ===== |
en/navody.txt · Last modified: 2023/01/15 12:59 by 94.112.192.193