en:navody
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
en:navody [2019/01/30 15:28] – [Modules] fluktuacia | en:navody [2023/01/15 09:43] – old revision restored (2019/01/31 14:11) 94.112.192.193 | ||
---|---|---|---|
Line 162: | Line 162: | ||
=== Screw terminal === | === Screw terminal === | ||
- | There are two widespread | + | There are two widespread |
The first type is more common mostly due to its low price. However, thanks to using a sheet metal washer under screws, it is not possible to fasten a naked wire of small diameter well into this type of screw terminal. Furthermore, | The first type is more common mostly due to its low price. However, thanks to using a sheet metal washer under screws, it is not possible to fasten a naked wire of small diameter well into this type of screw terminal. Furthermore, | ||
Line 174: | Line 174: | ||
=== Spring terminal block === | === Spring terminal block === | ||
- | Spring terminal block are an excellent modern substitute for screw terminals, which are slowly becoming technically obsolete. Their disadvantage, | + | Spring terminal block are an excellent modern substitute for screw terminals, which are slowly becoming technically obsolete. Their disadvantage, |
One of the commonly used spring terminal block is WAGO256. | One of the commonly used spring terminal block is WAGO256. | ||
Line 184: | Line 184: | ||
==== High-frequency signals ==== | ==== High-frequency signals ==== | ||
- | High-frequency signals are led to external devices in the same way as they are between modules - via coaxial | + | High-frequency signals are led to external devices in the same way as they are between modules - via coaxial |
In order to connect distant devices, such as receiving antenna, F-connector is a good choice, mainly thanks to its easy assembly and disassembly, | In order to connect distant devices, such as receiving antenna, F-connector is a good choice, mainly thanks to its easy assembly and disassembly, | ||
Line 191: | Line 192: | ||
=== USB === | === USB === | ||
- | The most widely | + | The most widely |
{{: | {{: | ||
- | Using an USB connector on a module requires placing a current fuse into the charing from USB (usually 750mA PTC). Otherwise a short circuit can cause a fall of HOST system and thus a data loss (of a tuned program). | + | Using a USB connector on a module requires placing a current fuse into the charing from USB (usually 750mA PTC). Otherwise a short circuit can cause a fall of HOST system and thus a data loss (of a tuned program). |
=== RS-232 === | === RS-232 === | ||
Line 203: | Line 204: | ||
=== RS-485 === | === RS-485 === | ||
- | In industry, this bus is used with terminal blocks. Therefore it is suitable | + | In industry, this bus is used with terminal blocks. Therefore it is practical |
=== CAN === | === CAN === | ||
- | To distribute CAN bus over longer | + | To distribute CAN bus over longer |
===== Test constructions ===== | ===== Test constructions ===== | ||
Line 220: | Line 221: | ||
==== Measuring arrangement ==== | ==== Measuring arrangement ==== | ||
- | The following way of assembly, when we use úhelníky (??), for example form Merkur building kit, in order to attach the corner screws, has an advantage in that you can access both sides of the board without any problems and carry out measurements also on a PCB. It is thus suitable for revive | + | The following way of assembly, when we use úhelníky (??), for example form Merkur building kit, in order to attach the corner screws, has an advantage in that you can access both sides of the board without any problems and carry out measurements also on a PCB. It is thus suitable for reviving |
{{: | {{: | ||
Line 232: | Line 233: | ||
==== Tower arrangement ==== | ==== Tower arrangement ==== | ||
- | Metal MLAB mounts can be stack on onto another using threaded rods. Such arrangement saves space and enables a construction of a more complicated and extensive | + | Metal MLAB mounts can be stack on onto another using threaded rods. Such arrangement saves space and enables a construction of more complicated and large-scale |
{{: | {{: | ||
- | The threaded rods used in the example are of M5 type and each board is fastened by a nut from above and below. There are washer | + | The threaded rods used in the example are of M5 type and each board is fastened by a nut from above and below. There are washers |
===== Permanent installations ===== | ===== Permanent installations ===== |
en/navody.txt · Last modified: 2023/01/15 12:59 by 94.112.192.193