en:rules
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
en:rules [2019/02/08 14:06] – fluktuacia | en:rules [2019/02/09 15:19] – fluktuacia | ||
---|---|---|---|
Line 247: | Line 247: | ||
Modules’ indicator LEDs are preferably designed in a way that they shine through the PCB onto the side turned away from the base board. It can be achieved by placing a LED into a hole in a PCB - such kind of mounting is called “reverse mount” and there exist [[http:// | Modules’ indicator LEDs are preferably designed in a way that they shine through the PCB onto the side turned away from the base board. It can be achieved by placing a LED into a hole in a PCB - such kind of mounting is called “reverse mount” and there exist [[http:// | ||
- | Classic THT LED with through feet (?? Led s průchozími nožičkami) | + | Classic THT LEDs with through feet (?? Led s průchozími nožičkami) |
- | Klasické THT LED s průchozími nožičkami se osazují s montážní podložkou, která usnadňuje osazování chrání led před zbytečným tepelným namáháním a ohybem. | + | |
- | === Krystaly | + | === Crystals |
- | Pro krystaly v modulech | + | As a basic case for crystals in MLAB modules, we have chosen |
- | {{: | + | {{: |
- | Pro moduly, kde lze předpokládat občasnou výměnu krystalu za krystal s jinou frekvencí se na modulech osazuje speciální držák krystalu, do kterého je možné po zkrácení nožiček krystal pohodlně zasunout | + | In case of modules, where we assume occasional exchanges of crystals for crystals with other frequencies, we fit them with a special crystal holder. After shortening the legs, crystals can be comfortably inserted into the holder and thus replaced by another crystal any time. |
- | {{: | + | {{: |
- | === Rezervní pozice pro součástky | + | === Backup positions for components |
- | Indikační LED mohou na modulech být v provedení | + | Modules’ indicator LEDs can be of SMD or LED 3 mm types. SMD diodes can be placed also on the bottom side of the board that is turned towards the base plate. In such case, it is recommended to design a hole of approximately 1 mm in diameter over the SMD LED, through which the LED will be visible. |
- | ===== Potisk | + | ===== Text / Printing (?? Potisk) on modules |
- | Potisk na modulech by měl respektovat obecná typografická pravidla. Je to důležité hlavně z hlediska nutnosti zachovat čitelnost potisku i po aplikaci sítotiskem. | + | Modules’ printings should respect a general typographical rules in order for it to be readable even after an application of screen printing. |
- | ==== Písmo | + | ==== Font ==== |
- | Na jednom modulu se může vyskytovat více velikostí písma, | + | One module can accommodate more font sizes (usually less than 3 is necessary). They are used in a following order: name of the module, printings (??), warnings, author’s id. Different sizes are of course used only in cases, when there is enough space on the module. Some modules have therefore only one font size - with respect to good readability and module’s size. |
- | === Zarovnání | + | === Alignment |
+ | |||
+ | Same priority signals should have the same font size across the whole module. Size and a style of individual labels should also united in case of one connector. | ||
- | Signály se stejnou prioritou by měly mít na celém modulu jednotnou velikost písma. Taktéž by měla být sjednocena velikost a styl jednotlivých popisků u jednoho konektoru. | ||
Popisky jednotlivých signálů na hřebínku se zarovnávají ke konektoru, aby byla minimalizována možnost řádkové chyby při zapojování. | Popisky jednotlivých signálů na hřebínku se zarovnávají ke konektoru, aby byla minimalizována možnost řádkové chyby při zapojování. |
en/rules.txt · Last modified: 2023/02/03 00:14 by kaklik