Differences

This shows you the differences between two versions of the page.

--- en:vmds [2013/06/19 08:32] – created kaklik
+++ en:vmds [2017/01/06 22:25] – [Visual observer] fluktuacia
@@ Line 1: / Line 1: @@
-====== Visual Meteor Detekction Station ======
+FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)//
+====== Visual Meteor Detection Station VMDS01A ======
+===== Technical equipment =====
+Following technical equipment is used by a visual meteor detection amateur network [[http://cement.fireball.sk/test-kamery-kpf-131-hr/|CEMeNt]].
+==== Lens ====
+The lens has to be sufficiently wide angled and luminous - conditions so far best met by [[http://www.t-cz.com/cctv-lens-tokina-3-8-2-mm-f0-98-ir-_d5404.html|Tokina 3-8.2 mm F0.98 (IR)]].
+==== A use of KPF 131HR camera ====
+[[http://www.elnika.cz/elnika.php?p=cze/specifikace-produktu/12316|KPF 131HR cammera]] is originally designed for building surveillance and thus requires several technical changes in order to make is suitable for usage.
+=== IR filter removal from CCD chip ===
+The most essential change of the camera is the removal of the IR cut filter. Proceed as follows:
+{{:cs:designs:vmds:opening_kpf131hr_camera.jpg?direct&200|}} {{:cs:designs:vmds:kpf131hr_camera_opened.jpg?direct&200|}}  {{:cs:designs:vmds:ccd_chip_umounting.jpg?direct&200|CCD chip un-mouting}} {{:cs:designs:vmds:ccd_chip_light_sealing.jpg?direct&200|CCD chip light sealing removing}} {{:cs:designs:vmds:camera_ircut.jpg?direct&200|IR cut filter on chip}}
+{{:cs:designs:vmds:ircut_filter_removing.jpg?direct&200|IR cut filter removing}} {{:cs:designs:vmds:ircut_filter_removing_complete.jpg?direct&200|Removed IR filter}} {{:cs:designs:vmds:light_seal_return.jpg?direct&200|Returning the light seal}}
+=== LED disconnecting ===
+At the back of the camera you find a continuously shining LED, that might cause reflections from the front cover glass at night. It is therefore recommended to disconnect it during the IR filter removal.
+{{:cs:designs:vmds:removing_led_supply.jpg?direct&200|Unsoldering the resistance powering the LED}}
+=== Camera settings ===
+PRC correction? Dark frame?
+Before usage the camera has to be set as follows:
+  * exposition 1/50 s
+  * aperture control DC
+  * BW regime
+  * AGC to middle
+  * brightness ca. 75
+==== ImagingSource camera  ====
+The manual uses [[http://www.theimagingsource.com/en_US/products/cameras/usb-ccd-color/dfk72auc02/|DFK 72AUC02]] camera.
+=== How to make the camera work in Ubuntu ===
+  - https://github.com/TheImagingSource/tiscamera/wiki/Getting%20Started%20with%20USB%20cameras
+     upgrade of the camera firmware was done according to instructions with 2 exceptions:
+      - git clone https://github.com/TheImagingSource/tiscamera.git
+      - sudo ./euvccam-fw -u ../../data/firmware/usb2/dmk72uc02_129.euvc
+Now it is possible to see the camera in /dev/video0
+. Further it is necessary to instal ucview [[http://rsbotics.wordpress.com/2012/05/18/how-to-get-a-working-version-of-unicap-and-ucview/|exactly according to instructions]] and then to install libunicapgtk2 from
+Ubuntu repository.
+  sudo apt-get install git autoconf libtool libgettextpo0 gettext gtk-doc-tools libraw1394-dev libpango1.0-dev libgstreamer0.10-dev libxv-dev  libgtk2.0-dev libgconf2-dev libglade2-dev libglade2.0 libglademm-2.4-dev libgstreamer-ocaml-dev libgstreamer-plugins-base0.10-dev
+  git clone https://github.com/unicap/unicap.git ; cd unicap
+  cd libunicap
+  ./autogen.sh ; ./configure ; make ; sudo make install
+  cd ../libucil
+  ./autogen.sh ;  ./configure; make; sudo make install
+  cd ../libunicapgtk/
+  ./autogen.sh ;  ./configure; make; sudo make install
+Compile the ucview.
+  git clone https://github.com/kaklik/ucview ; cd ucview/trunk
+  cd ucview
+  ./autogen.sh;  ./configure; make; sudo make install
+  cd ../ucview-plugins/
+  ./autogen.sh; ./configure; make; sudo make install
+  make; sudo make install
+To test if everything got compiled fine run
+  ucview
+Note: On some system you may need root privileges while running ucview to get your camera working.
+=== Issus with currently used cameras ===
+  * Signal transmission is not possible over longer distances (in orders of meters). This means, that computer has to be very close to the cameras usually under often problematic weather conditions.
+  * Small angular resolution of camera
+  * Small dynamic range
+=== TODO ===
+  * Software for synthesized all sky camera.
+==== Protection of camera ====
+Camera placed in a way that it has direct view to the ecliptic has to be protected against direct sunshine that may damage the CCD chip.
+It is customary to use a timer, that would close a camera shutter during a day by means of cutting off the power source.
+[[http://eshop.elkoep.cz/sht-4-----detail-8BW0000101.aspx|time protection of camera from the direct sunlight]]
+This method is not very advantageous because of the additional timer, that could be replaced by the station's computer. Moreover, the situation could be addressed using the same method as in [[en:mrakomer4|MRAKOMĚRu4]].
+===== Software =====
+==== MetRec ====
+[[http://www.metrec.org/|MetRec]] is a freeware software that uses its own Matrox Meteor II card (has to be purchased) to grab the signal.
+==== UFOCapture ====
+[[http://sonotaco.com/soft/e_index.html|UFOCapture]] is a proprietary software for Windows. It works with any grabbing hardware.
+==== AZcendant ====
+[[http://www.azcendant.com/MotionDetection.html|HandyAVI]]
+==== Visual observer ====
+The drawbacks of the currently used programmes for automatic detection of meteor trails could be addressed by a new OpenSource software. It is so far still just a concept - comments are found here:
+ [[http://www.mlab.cz/redmine/projects/visob|Redmine]].
+A final version of detection software should use an [[en:opsa|OPSA01A]] based camera as an visual data input.
+=== Syntéza celooblohového obrazu ===
+Celohoblohovy kamerovy system  (celooblohova kamera slozena z vice kamer) do snimaneho obrazu rovnou kreslit souradnicovou sit. Podle aktualniho casu. (Vyuzit mozna automaticke identifikace vyznamnych objektu v obrazu)
+===== Využití dat =====
+==== Bolidozor ====
+[[http://wiki.bolidozor.cz|Síť Bolidozor]] se jistě bude snažit o využití pozorovaných dat pro detekci bolidů a jejich následné vyhledávání.
+==== Meteorologie ====
+Protože kamery této stanice by měly být směrovány tak, aby zabíraly oblohu, tak pozorovaná data lze také teoreticky využít pro meteorologické aplikace. Neboť oblačnost sledovaná zespodu z menší vzdálenosti může poskytovat cenné informace o výskytu stoupavých proudů, parametrech bouřek, nebo o postupu front.
+Fotometricky může být také měřena výška základny oblačnosti, nebo její tloušťka, úroveň pokrytí.
+Dalším užitečným výstupem může být koncentrace prachu a aerosolů v atmosféře.
+==== 3D rekonstrukce obrazu ====
+  * [[http://openmvg.readthedocs.org/en/latest/software/MVS/MVS/|OpenMVG]]
+  * [[https://github.com/albertcheng/bundler_sfm|Bundler]]
+  * [[https://github.com/kml27/insight3d/tree/master/insight3d|insight3d]]
+===== Reference =====
+  * Síť [[http://cement.fireball.sk/|CEMeNt]]
+  * Ukázka [[http://www.astrozor.cz/index.php?udalost=56|Realizace stanice na Hvězdárně Svákov]]