MLAB wiki

Máte načtenou starší verzi dokumentu! Pokud ji uložíte, vytvoříte tím novou aktuální verzi.

====== Žabincosběrač I ======

Loď na uklízení žabince z rybníku.

[[http://www.youtube.com/user/kaklcz#p/a/u/0/NQGEWCW1xCg|Žabincosběrač v akci]]

Brushless Motor Controller (ESC)
Thanks for using Turborix (AE) Brushless Motor Controllers. Please read the instructions
carefully before you start to use new controllers.
The ESCs use higher quality micro processor and more FETs with lower intemal
resistance. As such, they outperform many other ESCs. In particular, they have extremely
performance-cost ratio.
Technical details:
Model Current (A) BEC Cells Weight (g)
FM10A 10 Max 1A NiCd/NiMh 6-12 10
Li-Po
FM20A
20
Max 2A
NiCd/NiMh 6-12
Li-Po
FM30A
30
Max 3A
40
OPTO
FM60A
60
OPTO
FM80A
80
OPTO
FM120A
120
OPTO
55
3-6
NiCd/NiMh 8-18
Li-Po
55
3-6
NiCd/NiMh 8-18
Li-Po
35
3-6
NiCd/NiMh 8-18
Li-Po
25
2-3
NiCd/NiMh 8-18
Li-Po
18
2-3
NiCd/NiMh 6-12
Li-Po
FM40A
2-3
78
3-6
Diagram for FM10A, FM20A, FM30A
DC Power
ESC
BEC
Throttle
signal
(Receiver)
Signal from receiver and
provide power to receiver
Diagram For FM40A, FM60A ,FM80A, FM120A
DC Power
ESC
BEC
Throttle signal (Receiver)
Signal from receiver
5V DC power
Main functions:
1. Safety mode: the motor won’t start no matter what the position of the control stick is
when switched on the RC unit. When the throttle is not at lowest or Max position, it will
sound by “di-di-di” for warning.2. Brake: On / Off (factory setting is Off).
3. Battery type: NiCd/NiMh, LiPo.
4. Number of batteries: automatic (when setting Battery Type, the ESC will set Number
of Batteries automatically at the same time)
5. Start up mode: Soft start up, Hard start up
6. Timing mode: Soft timing-for 2, 4, 6 pole brushless motors, Hard timing-for 6 and more
pole motors, Auto
7. Temperature protection: the controller will reduce output power when temperature
reaches 120 degrees centigrade
8. Low voltage protection: reduce output power when the voltage goes down below the
setting (setting of low voltage is 2.8V times number of batteries)
Operating instructions:
- Normal start up:
Connect the controller and motor as above connection drawing. Switch on the transmitter
and check the throttle stick at lowest position. Connect the main power pack and switch on
BEC (for the controllers with “beeps” – Brake On, now you can begin flying. If the throttle
stick is not at lowest position, you will hear “di-di-di”, that alarms you moving the stick to
lowest position.
- Set up by Throttle Stick:
Connect controller with motor as above connection diagram. Switch on the transmitter and
check the throttle stick is at Max position. Connect the main power pack and switch on
BEC (for the controllers with BEC). After a piece of music, you can follow the prompting
sound to begin programming. When hear a prompting sound (sound 3 times), move the
throttle stick from high to low position quickly. You should hear a “beep”, your setting is
done. Move the stick back to Max position, waiting for the prompting sound and repeat
above steps for other settings. After your setting, keep the stick at lowest position for 5
seconds, you will hear a piece of music. Now, you can begin flying.
Prompting Sound:
1. Brake On: - - -
2. Brake Off: - - - - - -
3. NiCd / NiMh: . - . - . -
4. LiPo: . -- . -- . –
5. Soft Start up: .. - .. - .. –
6. Hard Start up: .. -- .. -- .. –
7. Soft Timing: ... “ ...” ...”
8. Hard Timing: ,,, -- ,,, -- ,,, --
9. Reset to Factory Setting: ... ... ...
The controllers are supplied with factory setting, Brake Off, Soft start up and Auto timing.
Note: when the first time of using the ESC, or when changing number of batteries,
or when changing battery type, the setting of Battery Type must be done every time.
Programming Card:
Turborix (AE) ESC can be programmed by a E-PRG-1 programming card. It will expand
ESC’s functions and suitability. Details please see the instructions of E-PRG-1
Programming Card.Notice:
1. Every Turborix (AE) ESC of FM10A, FM20A and FM30a has a BEC plug (JR
connector), it is for connecting to receiver and also for connecting to Programming
Card. For FM40A, FM60A, FM80A and FM120A there are two JR connectors on each
ESC. The one with long wire is for connecting to receiver. The one with short wire is
for connecting to Programming Card.
2. Choose suitable brushless motors and propellers, ensure the working current never
exceed specified current of ESC.
3. Make sure the connecting for battery positive and negative is right. Reversing the
connection will damage the ESC permanently.
4. Use suitable batteries, do not exceed specified voltage of ESC.
5. Do not disassemble the ESC by self, it will damage the ESC or lose message.
6. The ESCs are designed for airplane models only.
7. Take care in using safely. Incorrect use may cause injury to the body. The company
will not be responsible for any damage or loss caused by incorrect operation.
8. Reverse the motor direction by exchanging the position of any two connections to the
motor.
Warning:
The propellers on turning are dangerous. Disconnect the main power
pack immediately after flying.
Turborix (AE) keeps the rights to change design, function or package,
without notice.

Vyplňte, prosím, všechna písmena v poli, abyste dokázali, že nejste robot. U W R A U Ponechte prosím toto pole prázdné:

Komentář k úpravám

Poznámka: Tím, že editujete tuto stránku, souhlasíte, aby váš obsah byl licencován pod následující licencí: CC Attribution-Noncommercial-Share Alike 4.0 International