MLAB wiki

Máte načtenou starší verzi dokumentu! Pokud ji uložíte, vytvoříte tím novou aktuální verzi.

====== Žabincosběrač I ======

Loď na uklízení žabince z rybníku.

[[http://www.youtube.com/user/kaklcz#p/a/u/0/NQGEWCW1xCg|Žabincosběrač v akci]]

===== Brushless Motor Controller (ESC) =====

Turborix (AE) Brushless Motor Controllers. Please read the instructions
carefully before you start to use new controllers.
The ESCs use higher quality micro processor and more FETs with lower intemal
resistance. As such, they outperform many other ESCs. In particular, they have extremely
performance-cost ratio.

[[http://www.mlab.cz/WebSVN/filedetails.php?repname=MLAB&path=%2FDesigns%2Fduckweed_collector%2FDOC%2FTurborix_AE_BrushlessMotorController.pdf|Manual]]
==== Technical details: ====
Model FM10A
Current 10 (A) 
BEC Max 1A
Cells NiCd/NiMh 6-12; 2-3 Li-Po
Weight 10 (g)

Main functions:
1. Safety mode: the motor won’t start no matter what the position of the control stick is
when switched on the RC unit. When the throttle is not at lowest or Max position, it will
sound by “di-di-di” for warning.

2. Brake: On / Off (factory setting is Off).

3. Battery type: NiCd/NiMh, LiPo.

4. Number of batteries: automatic (when setting Battery Type, the ESC will set Number
of Batteries automatically at the same time)

5. Start up mode: Soft start up, Hard start up

6. Timing mode: Soft timing-for 2, 4, 6 pole brushless motors, Hard timing-for 6 and more
pole motors, Auto

7. Temperature protection: the controller will reduce output power when temperature
reaches 120 degrees centigrade

8. Low voltage protection: reduce output power when the voltage goes down below the
setting (setting of low voltage is 2.8V times number of batteries)

Operating instructions:

- Normal start up:

Connect the controller and motor as above connection drawing. Switch on the transmitter
and check the throttle stick at lowest position. Connect the main power pack and switch on
BEC (for the controllers with “beeps” – Brake On, now you can begin flying. If the throttle
stick is not at lowest position, you will hear “di-di-di”, that alarms you moving the stick to
lowest position.

- Set up by Throttle Stick:
Connect controller with motor as above connection diagram. Switch on the transmitter and
check the throttle stick is at Max position. Connect the main power pack and switch on
BEC (for the controllers with BEC). After a piece of music, you can follow the prompting
sound to begin programming. When hear a prompting sound (sound 3 times), move the
throttle stick from high to low position quickly. You should hear a “beep”, your setting is
done. Move the stick back to Max position, waiting for the prompting sound and repeat
above steps for other settings. After your setting, keep the stick at lowest position for 5
seconds, you will hear a piece of music. Now, you can begin flying.

Prompting Sound:

1. Brake On: - - -

2. Brake Off: - - - - - -

3. NiCd / NiMh: . - . - . -

4. LiPo: . -- . -- . –

5. Soft Start up: .. - .. - .. –

6. Hard Start up: .. -- .. -- .. –

7. Soft Timing: ... “ ...” ...”

8. Hard Timing: ,,, -- ,,, -- ,,, --

9. Reset to Factory Setting: ... ... ...

The controllers are supplied with factory setting, Brake Off, Soft start up and Auto timing.
Note: when the first time of using the ESC, or when changing number of batteries,
or when changing battery type, the setting of Battery Type must be done every time.

==== TODO ====

=== Dálkové ovládání ===

* Nahradit mechanický křížový ovladač magnetickým joystickem tisknutelným na 3D tiskárně.
  * Zvážit nahrazení ovladače smartphonem. 
  * Použít modul [[cs:ant]]

=== Loď ===

* Vyřešit vícečlánkové napájení modulem [[cs:lion2cell]]
  * Zatáčení kormidlem na servu nahradit dvěma dmychadly s krytými vrtulemi.
  * Upravit konstrukci jako nosnou pro ponorku.

Vyplňte, prosím, všechna písmena v poli, abyste dokázali, že nejste robot. X E G D᠎ S Ponechte prosím toto pole prázdné:

Komentář k úpravám

Poznámka: Tím, že editujete tuto stránku, souhlasíte, aby váš obsah byl licencován pod následující licencí: CC Attribution-Noncommercial-Share Alike 4.0 International