User Tools

Site Tools


en:lna

Differences

This shows you the differences between two versions of the page.


Previous revision
en:lna [2013/07/25 08:03] fluktuacia
Line 1: Line 1:
-====== Low-noise amplifier LNA01A ====== 
- 
-A low-noise preamplifier module ([[http://en.wikipedia.org/wiki/Low-noise_amplifier|LNA]]). The original construction is intended to be used in bands around 143MHz, but it is probable, that it can be used in other bands as well, as the used transistor [[http://www.avagotech.com/pages/en/rf_microwave/transistors/fet/atf-53189/|ATF-53189]] shows good characteristics up to approximately 6GHz.  
- 
- 
-===== Construction ===== 
- 
-The connection of the amplifier is implemented using the FR4 PCB. It is possible to fit the PCB with straight SMA connectors or edge connectors. The amplifier is expected to be placed inside the metallic shielding box. 
- 
-The following scheme shows the circuit of the module: [[http://www.mlab.cz/WebSVN/filedetails.php?repname=MLAB&path=%2FModules%2FCommRF%2FLNA01A%2FSCH%2FLNA.pdf| LNA01A scheme]].  
- 
- 
-===== Tuning ===== 
- 
-The amplifier tuned to 143MHz band: 
- 
-{{:cs:lna01a_assembled.jpg?direct&200|Assembled preamplifier LNA01A without the shielding can.}} 
- 
-{{:cs:lna01a_measuring_setup.jpg?direct&200|Arrangement for measuring.}} 
- 
-The transmission curve of the LNA01A. 
-Smaller horizontal lines in the upper part of the screen have a scale increment of 10MHz, increment for larger lines is 100MHz and 200MHz. The gain is approximately 27 dB.   
- 
-{{:cs:lna01a_transmission_curve.jpg?direct&200|LNA01A transmission curve}} 
- 
-A coil performing on 144Mhz has 7 turns of 0.5mm wire around a rod with a diameter of 4mm (__a drill__). The coil is stretched as seen in the picture. The capacitors C1 and C2 have the capacitance of 8,2 pF. It is not necessary to use a feedback on LNA, as it increases the __s/n ratio__ and decreases the gain by approximately 1dB. A trim is replaced by a 45 Ω resistor and the total current through the LNA should be around 153mA. The current through source transistor is than about 135mA.  
- 
-====== The measured parameters ====== 
- 
-{{:cs:prenos.png?200|}} 
- 
-{{:cs:lna_-10dbm_in.png?200|}} 
-{{:cs:lna01a_-20dbm_in.png?200|}} 
- 
-===== Applications ===== 
- 
-This preamplifier is primarily constructed for use in combination with SDR receiver [[en:sdrx|SDRX01B]]. Its characteristics are optimized for use in radioastronomy or cosmic research.  
- 
- 
-===== Covering ===== 
- 
-The module fits into metallic shielding box[[http://www.gme.cz/plechove-krabicky-stinici-cinovane/u-ah101-p622-024/|U-AH101]] 
- 
- 
-== References == 
-  * [[http://www.ha8et.hu/PDF/EXTRA-2%20144%20MHz%20Contest%20Preamplifier.pdf|Extra-2]] - the original HA8ET construction 
  
en/lna.txt · Last modified: 2015/03/23 16:54 (external edit)