en:navody
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
en:navody [2019/02/03 14:43] – fluktuacia | en:navody [2023/01/15 09:43] – old revision restored (2019/01/31 14:11) 94.112.192.193 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | + | ====== General hints concerning modules ====== |
- | ====== Rules for designing new modules | + | This page sums up the possibilities and means of MLAB modules' use. The individual paragraphs contain various different applications and special cases. |
- | This page serves as a wiki complement to an original article | + | Beginners can make us of [[en:guide|a guide for beginners]]. |
- | The module design itself uses a following [[en: | + | ===== Obtaining |
- | ===== Identification of modules | + | In order to begin a construction, |
- | Each modules has to carry a unambiguous identification mark consisting of its name, version and module revision - e.g. [[cs: | + | ===== Tools ===== |
- | - JTAGFT2232 - the name of the module, depicting the nature of the module (here probably a J-tag programmer with FTDI FT2232 chip). | + | ==== Mechanical tools ==== |
- | - (V)02 - the module’s version - there already were some crucial changes during the modules development (in this case, there was CPLD added from version 01) | + | |
- | - A - the module’s revision (in this case there were not corrections of any mistakes) | + | |
- | Furthermore there are modules | + | Work with MLAB modules |
+ | {{: | ||
- | * **Green mask and white print** - a prototype module, often made only in one or few pieces serving as testing samples | ||
- | * **White mask and black print** - a production version made in large quantities. Compared to the green version, it may contain tiny changes changes even if the module’s identification mark is identical. | ||
- | ===== Creating a new module ===== | + | ==== Electronic tools ==== |
- | ==== Using a mlabgen script | + | |
- | The first step is to create a correct directory structure of a new module in the [[https:// | + | === Multimeter === |
- | | + | |
- | The directory structure can be created either manually or using a | + | Multimeter of almost any type is sufficient, however we recommend |
- | mlabgen-module-init NAMEVERREV | + | {{: |
- | The '' | + | More advanced users can use [[en:ut804|a table multimeter]]. |
- | Using the '' | + | === Oscilloscope === |
- | Next step is to edit the metadata file ''< | + | An oscilloscope |
+ | |||
+ | {{:rigol_ds1052e.jpg? | ||
- | Commit log should be completed with an information that a new module has been added together with its purpose. Further documentation should be already created during the module development. It is therefore useful to create a module’s wiki page here, shorty after the commit of the new module. Creating a page can be done by opening a wiki page from the [[https:// | ||
- | ==== Manual module creation | + | === Soldering iron === |
- | If, for some reason, you are reluctant to use MLABgen for creation of the basic directory structure, it is necessary to comply with the following rules: | + | |
- | In the appropriate folder category we create a folder with the name of the new module using a format '' | + | A soldering iron is not necessary for most of the MLAB constructions, |
- | Inside the folder, we create the following directory structure (obligatory folders/files are marked with an asterisk): | + | |
+ | {{: | ||
- | < | + | It is even possible to agree on purchasing a 100W version with parameters exceeding even high class micro soldering irons from Weller. |
- | ├── doc* | + | |
- | │ ├── img* | + | When soldering peaces like connectors or thick wires and tinned sheet metal boxes, it is more practical to use a transformer soldering iron because of its higher heat power (150W). |
- | │ │ ├── < | + | |
- | │ │ └── < | + | |
- | + | ||
- | │ │ └── | + | |
- | │ ├── < | + | |
- | │ ├── < | + | |
- | │ └── src | + | |
- | │ | + | |
- | ├── hw | + | |
- | │ ├── cam_profi | + | |
- | │ │ ├── < | + | |
- | │ │ . | + | |
- | │ │ . | + | |
- | │ │ └── < | + | |
- | │ └── sch_pcb | + | |
- | │ | + | |
- | │ | + | |
- | │ | + | |
- | ├── cad | + | |
- | │ ├── src | + | |
- | │ │ | + | |
- | │ └amf | + | |
- | │ | + | |
- | ├── < | + | |
- | | + | |
- | └── < | + | |
- | The file ''< | + | {{: |
- | { | + | When buying a transformer soldering iron, make sure you are buying the one with a horizontal soldering tip, as shown on the picture. Transformer soldering irons with vertical tips are more suitable for sheet soldering or welding / cutting of plastics. |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | " | + | |
- | } | + | |
- | You can find example | + | **All types of soldering irons require |
- | ===== Module power supply ===== | + | === An aid for smoke extraction |
- | You can find more detailed examples | + | During any soldering, the evaporated flux creates a very unpleasant smoke that irritates the respiratory tract. One of the solutions is to build a simple aid from an older PC ventilator. Connect it to an adjustable power supply |
- | ==== MLAB connectors configuration | + | ==== Using the tools ==== |
- | Power supply connectors for low currents have two configurations (??) which are implemented using .. (??) | ||
- | Napájecí konektory pro nízké proudy mají dvě konfigurace a jsou realizovány lámacími hřebínky s roztečí 2,54mm | ||
- | {{: | + | === Connecting the oscilloscope probe === |
- | **Power supply connectors are doubled in order to allow smyčkování napájení | + | An oscilloscope’s probe ground can be easily connected |
- | ==== Externí napájecí zdroje ==== | + | |
- | For power supply with higher powers, the FASTON connectors or WAGO256 | + | The signal probe input can be connected to MLAB in a following way: the connecting cable is cut to half, part of the cable is stripped of an insulation and a crimp pin connector is crimped onto the cable. Now the cable, via the crimp pin connector, can be easily attached to the probe’s hook and its second end with the original PC terminal, can be connected to the pinch outlets of all modules. |
- | {{ : | + | ===== Connecting of modules ===== |
- | There are always openings for WAGO256 terminal block on PCB, because | + | Modules |
- | === Cylindrical power supply | + | ==== Power supply |
- | === Power supply +5V from USB === | + | Power provided by [[en: |
- | It is always a good practice to include a safety current PTC fuse into the USB power supply | + | === Power supply |
- | === High voltage | + | This power voltage |
+ | {{: | ||
- | Pro rozvod vysokého napětí k modulům (>250V DC) se používají speciální vysokonapěťové konektory [[http:// | + | == 3.3V == |
- | {{: | + | Power voltage of 3.3 V is lead by the same cable as the +5V power supply, only the red wire is replaced by an orange one. |
- | Vzhledem k běžně velmi dobrým izolačním vlastnostem koaxiálních kabelů je možné použít pro výrobu vysokonapěťových rozvodů i koaxiální kabel RG58. | + | === Voltage higher than +5V === |
- | + | ||
- | ===== Ochranné prvky na modulech ===== | + | |
+ | This category usually involves 7.2 (2x Li-ion cell) or +12V (lead-acid battery or other power supplies). For safety reasons it is therefore led via a yellow (+) and black (-) cable, following an example of ATX power supplies. Connectors are four-pin, the middle two pins being + and the outer two -/GND. The connector is symmetrical, | ||
- | ==== Schéma modulu ==== | + | {{: |
- | Správně nakreslené schéma (nejenom modulů MLAB) dodržuje tyto zásady: | + | === Symmetrical power supply === |
- | | + | This kind of power supply, conventionally +12V and -12V, is used in analogue constructions, which are using operational amplifiers. It is distributed by power cables with 5 pins - the middle + two pins are positioned symmetrically around the central |
- | - Signály vedou zleva doprava. | + | |
- | - Kladné napájení vede ze shora dolu, záporné zespoda nahoru. | + | |
- | | + | |
- | | + | |
- | - na jednom spoji musí být minimální množství spojovacích bodů (není například vhodné kreslit vedle sebe dva T uzly ale lepší je nakreslit jeden uzel +). | + | |
- | - Hodnoty součástek musí mít jednotnou jmennou konvenci využívající plný název fyzikální veličiny tj. nF, pF atd. | + | |
- | Specifikem schémat MLABu pak je, že hřebínky jsou vždy ve dvojici ale ve schématu se pro přehlednost uvádí, jako jedna součástka. (vyžaduje to v některých případech použití vlastních knihoven, ale přehlednost schéma je tím podstatně zlepšena.) | + | {{: |
+ | === High voltage power supply === | ||
- | ==== Ochranné odpory ==== | + | In cases where we work with high currents (up to tens of Amperes) and, at the same time, high voltages (tens of Volts) (a typical example is a robot’s drive powered from an accumulator), |
- | Na vstupech některých modulů, jako jsou například čidla (nebo často moduly pracující na 3,3V) je vhodné umístit ochranné sériové odpory, které zvýší odolnost vůči externímu přepětí. Velikost těchto odporů se obvykle volí v rozsahu 10 Ohm až 1kOhm, podle předpokládaného potřebného proudu IO pinem. | + | === Very high voltage power supply === |
+ | It includes power voltage in range of hundreds of volts to ones of kV. Such powering is used for certain special detectors or gas discharge lamps, LASERs, etc. It is distributed via a coaxial cable with SHV or MHV connectors. | ||
- | ==== Ochranné diody ==== | + | ==== High-frequency signals |
+ | === Asymmetrical signals | ||
- | Prakticky všechny | + | Analogue VF signals are distributed in MLAB via a classic VF Pigtail usually made from coax RG-174 with both ends having a screw-type SMA (Male) connector. |
- | Proto není vhodné napájení modulů realizovat přímo z akumulátorů, | + | {{: |
- | ===== Geometrie modulů ===== | ||
- | ==== Rozměr ==== | + | **Caution** the connector in the picture contains a sample error - a missing shrinking tube over a crimped connector ferrule. Without it, there is gradual breaking of the cable sheet from the connector. |
- | Moduly jsou navrženy v rastru 10,16 mm (400mils) | + | **Crimped connectors’ ferrules have to be proteced by a shirnking tube! ** [[http:// |
- | Názorný příklad pro modul zabírající 3 otvory na ALBASE: | ||
+ | === Differential symmetrical signals | ||
- | {{ :cs:modul.png?400 |}} | + | Fast digital signals, such as those of AD converters’ clocks or sequence circuits, are in MLAB usually distributed differentially in order to limit interference. We usually use PECL or LVDS logic. Signals are lead via a standard direct (??) SATA cable - chosen for its defined impedance and good availability. |
+ | {{: | ||
- | | + | ==== Digital buses ==== |
- | | + | |
- | | + | |
- | | + | |
- | ==== Rohové šrouby ==== | + | Digital buses, such as I2C, TWI or 1-wire are distributed between the modules via standard cables, usually only adjusted so that one plastic ending contains all the bus’s wires, possibly together with a power supply. |
- | Šrouby musí mít okolo sebe dostatečný prostor pro utažení dvou kontra-matic, | + | ===== Maintenance and cleaning ===== |
- | Matice se u modulů používají proto, protože dvě matice umožňují využít efektu [[http:// | + | ==== Interconnecting cables ==== |
+ | Due to a gradual wear by a mechanical switching, the interconnecting cables’ connectors loose their conductivity. It lasts several hundreds of connections and re-connections until the phenomenon occurs, but it might be speeded up by a careless transport of already connected constructions, | ||
+ | The above-mentioned state can be repaired by napružení kontaktu konektoru (??) using a screwdriver or other similar tool. The procedure is done from outside at the connector' | ||
+ | ==== Modules ==== | ||
+ | Most of the modules do not require any additional maintenance. Sometimes it happens, that a dust piles up intensively onto modules. It might be solved either by blowing it away with an air blower ball (compressed air) or by brushing it off with an anti-static brush. | ||
+ | <WRAP info> It is not possible to use electrostatic duster for a dust removal as it might cause a destruction of certain electronic circuits in modules </ | ||
- | ==== Layout | + | When a module is extremely dirty, it can be cleaned in an ultrasonic cleaner. However, there are some modules |
- | **Mezní možnosti výroby: | + | ===== External connectors ===== |
- | Min. tloušťka cesty 0,1 mm | + | |
- | Min. izolační mezera 0,1 mm | + | |
+ | Connector for switching in other devices. | ||
- | Vedení plošných spojů a jejich rozměry jsou vždy volené tak, aby byla v co největší míře umožněna i amatérská výroba a osazení plošného spoje. | + | ==== Power supply ==== |
- | Spoje jsou dále vedeny tak, aby se co nejvíce minimalizovala možnost vyzařování modulu, což znamená minimální plochy smyček zvláště u spojů, které vedou střídavé proudy s velkou amplitudou, typicky měniče ale třeba i výstupy logických obvodů typu CMOS a TTL. | + | External power supply for MLAB modules is usually led by cylindrical connectors 5.5/2.1 mm to the main powering modules, e.g. UNIPOWER01A. |
- | U dvouvrstvých plošných spojů je preferováno užití horní strany modulu (odvrácené od základové desky) jako zemního potenciálu. V nutných případech je ale možné na této straně vést i nízkovýkonové napájení. Je ale nutné se v horní vrstvě vyvarovat vedení datových a vysokofrekvenčních signálů (opět kvůli možnosti vyzařování a snížení integrity signálu). | + | {{: |
- | Moduly by měly mít všechny čtyři šrouby spojené stejným potenciálem | + | Cylindrical connectors of different voltages are distinguished using a shrinking tube around a connector - yellow = 12V, red = 5V. |
- | === Pouzdra součástek === | + | Power supplies may also use a PC standard [[http:// |
- | Preferovaná pouzdra součástek jsou z našich [[https:// | + | In case of having a power supply supplied only from batteries, it is better to use e.g. BATPOWER02A module. When connecting accumulators, |
- | Proferovaná velikost SMD pouzder je aktuálně řada 0805. | + | {{: |
- | === Rozmisteni soucastek | + | ==== General terminal blocks ==== |
- | SMD součástky se umisťují výhradně na jednu stranu desky. Ideálně na stranu přivrácenou k základové desce (vrstva B.Cu). Důvodem je větší odolnost konstrukce, nižší vyzařování a ulehčení osazení v reflow peci. | + | === Screw terminal === |
+ | There are two widespread types of commonly used screw terminals on the market. Apart from a considerable difference in their costs, they also differ greatly in a quality and convenience of their use. | ||
- | === Vrstvy === | + | The first type is more common mostly due to its low price. However, thanks to using a sheet metal washer under screws, it is not possible to fasten a naked wire of small diameter well into this type of screw terminal. Furthermore, |
- | F.Cu - měděná vrstva ze strany součástek | + | {{:cs:bad-screw-terminal-block.jpg?200|}} |
- | B.Cu - měděná vrstva ze strany spojů | + | |
- | F.SilkS | + | |
- | B.SilkS - potisk strana spojů | + | |
- | F.Mask - maska strana součástek | + | |
- | B.Mask - maska strana spojů | + | |
- | Edge.Cuts - obrys desky | + | |
- | F.Fab - potisk pro osazování strana součástek | + | |
- | B.Fab - potisk pro osazování strana spojů | + | |
+ | The second type is more expensive, but does not experience the above mentioned problems. Furthermore, | ||
+ | |||
+ | {{: | ||
+ | |||
+ | === Spring terminal block === | ||
+ | Spring terminal block are an excellent modern substitute for screw terminals, which are slowly becoming technically obsolete. Their disadvantage, | ||
+ | One of the commonly used spring terminal block is WAGO256. | ||
- | Pri navrhu dvouvrstveho plosneho spoje, je jedna vrstva se vyhrazena pro zem a napajeni. Tato vrstva se | + | {{: |
- | pak nastaví jako " | + | |
- | napájení. To umožní automaticky ukončovat tyto spoje prokovem do této | + | |
- | vrstvy. | + | |
- | protoze v takovem případě se spoj špatně edituje. | + | |
- | === Prokovy === | ||
- | **Pro běžné cesty** | + | ==== High-frequency signals ==== |
- | 0,8 mm průměr prokovu a 0,4 mm průměr vrtání | + | |
- | + | ||
- | Pro silové cesty je potřeba zvětšit rozměry prokovu, dle přenášených proudů, nebo zvýšit jejich počet. | + | |
- | + | ||
- | + | ||
- | **Mez výroby** | + | |
- | Min. okruží 0,1 mm (průměr prokovu = průměr vrtání + 0,2 mm) | + | High-frequency signals are led to external devices in the same way as they are between modules - via coaxial cables with SMA connectors or they are connected via a short pigtail to some other panel [[http://en.wikipedia.org/ |
- | + | ||
- | V případech kde to není nutné nenavrhujeme na této mezi. Prodražuje cenu PCB. | + | |
+ | In order to connect distant devices, such as receiving antenna, F-connector is a good choice, mainly thanks to its easy assembly and disassembly, | ||
- | Texty v potisku modulu nesmí překrývat prokovy. (Jinak dojde k nečitelnosti potisku v místě prokovu) | + | ==== Data connectors ==== |
+ | === USB === | ||
- | ==== Konstrukční části ==== | + | The most widely found external bus used with modules is a [[http:// |
- | Na moduly kde zbývá volné místo na plošném spoje je možné umístit plošky pro rezervní součástky, | + | {{:cs:usb-b.jpg?200|USB connector on MLAB modules}} |
- | === LED === | + | Using a USB connector on a module requires placing a current fuse into the charing from USB (usually 750mA PTC). Otherwise a short circuit can cause a fall of HOST system and thus a data loss (of a tuned program). |
- | Indikační LED jsou na modulech ideálně navrhovány tak, aby svítily skrz plošný spoj na od základní desky odvrácenou stranu. Toho je dosaženo vsazením LED do díry v plošném spoji. Tento způsob montáže se označuje jako " | + | === RS-232 === |
- | Klasické THT LED s průchozími nožičkami se osazují s montážní podložkou, která usnadňuje osazování chrání led před zbytečným tepelným namáháním a ohybem. Montážní podložka mírně zvětší průměr základny LED s čímž je nutné počítat při návrhu plošného spoje. | + | Another data connector is [[http://en.wikipedia.org/ |
- | === Krystaly | + | === RS-485 |
- | Pro krystaly v modulech MLAB bylo jako základní pouzdro zvoleno HC49/S, malý krystal s nožičkovými vývody. Je to z toho důvodu, že může být umístěn na modulu z vrchní strany a je vždy viditelná jeho frekvence. Konstruktér tak má během laborování s moduly vždy přehled o používaných frekvencích. | + | In industry, this bus is used with terminal blocks. Therefore it is practical |
- | {{: | + | === CAN === |
- | Pro moduly, kde lze předpokládat občasnou výměnu krystalu za krystal s jinou frekvencí se na modulech osazuje speciální držák krystalu, do kterého je možné po zkrácení nožiček krystal pohodlně zasunout a kdykoli vyměnit za jiný. | + | To distribute CAN bus over longer distances, for example in house, we recommend using UTP cable and RJ-45 connectors. |
- | {{: | + | ===== Test constructions ===== |
+ | ==== Standard arrangement ==== | ||
- | === Rezervní pozice pro součástky === | + | Test constructions consist of one of the [[en: |
- | Indikační LED mohou na modulech být v provedení SMD, nebo LED 3mm. SMD diody lze umisťovat i na spodní stranu desky přivrácenou k podkladové desce. V takovém případě je ale vhodné do plošného spoje nad SMD LED navrhnout díru cca 1mm kterou bude SMD LED viditelná.. | + | {{: |
- | ===== Potisk na modulech ===== | ||
- | Potisk na modulech by měl respektovat obecná typografická pravidla. Je to důležité hlavně z hlediska nutnosti zachovat čitelnost potisku i po aplikaci sítotiskem. | + | ==== Measuring arrangement ==== |
- | ==== Písmo ==== | + | The following way of assembly, when we use úhelníky (??), for example form Merkur building kit, in order to attach the corner screws, has an advantage in that you can access both sides of the board without any problems and carry out measurements also on a PCB. It is thus suitable for reviving new modules. |
- | Na jednom modulu se může vyskytovat více velikostí písma, (obvykle na modulech stačí méně, než 3). Použivají se v pořadí: název modulu, popisky, výstrahy, označení autora. Různé velikosti se samozřejmě používají pouze v případech, | + | {{: |
- | === Zarovnání | + | ==== Direct mounting ==== |
- | Signály se stejnou prioritou by měly mít na celém modulu jednotnou velikost písma. Taktéž by měla být sjednocena velikost | + | Modules can also be screw directly to each other, |
- | Popisky jednotlivých signálů na hřebínku se zarovnávají ke konektoru, aby byla minimalizována možnost řádkové chyby při zapojování. | + | {{: |
- | === Velikosti Písma | + | ==== Tower arrangement ==== |
- | Nejčastější používané velikosti písma jsou: | + | Metal MLAB mounts can be stack on onto another using threaded rods. Such arrangement saves space and enables a construction of more complicated and large-scale systems. |
- | Width 1,5 mm, Height 1,5mm, Thickness 0,3mm - název modulu, důležité informace a popisky hřebínků | + | {{: |
- | Width 1,3 mm, Height 1,3mm, Thickness 0,3mm - popisky jednotlivých vývodů hřebínků | + | |
- | Velikost písma menší než 1,3 mm je problematická | + | The threaded rods used in the example are of M5 type and each board is fastened by a nut from above and below. There are washers between the board and the nuts. There is a spring washer used with one of the nuts. Cutting length (?? Řezná délka) in case of two boards above each other is 12 cm. This length was chosen because 1m threaded rod can be divided into 8 columns and there are 4cm left for cutout |
- | Na některých malých modulech může vzniknout problém s délkou názvu modulu, v takovém případě se název modulu zalamuje u verze modulu, například: | + | ===== Permanent installations ===== |
- | {{: | + | We can easily construct permanent or semi-permanent installations from the kit by screwing the tuned constructions with the base board to the bottom of the junction box. In order to increase the resistance against vibrations we can glue the přívody k hřebíkům (??) with a hot-melt adhesive and tie the cables to the base with a cable tie. Such construction is relatively cheap and, at the same time, robust and adjustable if necessary. |
- | ISL2902001A je celý název tohoto modulu, avšak ten není možné na modul umístit, proto je zalomen u verze jako ISL29020 | + | ==== Stand-alone construction ==== |
- | ==== QR kódy ==== | + | We can easily fit the module construction in the [[en:unibox|UNIBOX]] metal box. |
- | Na všechny moduly které jsou dostatečně velké, aby na ně mohl být umístěn QR kód. Ten obsahuje identifikaci modulu a odkaz na stránku s [[http:// | + | |
- | qrencode -s 15 -l L "http://www.mlab.cz/" | + | {{:cs: |
+ | |||
+ | ==== Installation into the distribution board ==== | ||
- | Pokud jste pro vytvoření modulu použili mlabgen, QRkód by měl být vytvořen při vytváření základní adresářové struktury. | + | In a similar manner, modules can be installed in the low-voltage parts of distribution boards. You can use plastic clips (??) (available at good electro shops) to attach them onto a DIN panel. |
- | <WRAP info round> | + | {{:wall_box_din_mount.jpg?200|MLAB in home distribution board}} |
- | Vhodnejší by pravděpodobně bylo použití [[http://www.qrcode.com/ | + | |
- | </ | + | |
+ | ==== Installation into the electrical box ==== | ||
- | === PADS === | + | Electrical box can be used in a similar way as a distribution board with one exception - there is usually not any problem with attaching the [[en:base1621|base board]]. |
- | + | ||
- | Miho pro potřeby generování kódu do potisku plošného spoje vytvořil | + | |
- | + | ||
- | * PADS Size: 20 | + | |
- | * PADS Line Width: 2 | + | |
- | + | ||
- | Vygenerovaný soubor je ve formě textu na spodní straně stránky. Text je tak nutné ručně vložit do souboru s příponou asc. Po importování vygenerovaného obrázku do potisku plošného spoje je následně třeba nastavit atribut "solid copper" | + | |
- | + | ||
- | === KiCAD === | + | |
- | + | ||
- | Obrázky QRkódů se do KiCAD [[http:// | + | |
- | + | ||
- | ===== Check list před výrobou ===== | + | |
- | + | ||
- | - zkontrolovat velikost a spravnost pouzder | + | |
- | - Velikost plosek u konektoru a soucastek skrz desku. | + | |
- | - velikost der, krystaly ledky, hrebinky, propojky, specialni soucastky. | + | |
- | - odmaskovani plošek, propojky | + | |
- | - obrysy soucastek, oznaceni propojek. | + | |
- | - popisky, napis www.mlab.cz | + | |
- | - Zkontrolovat, | + | |
- | - zkontrolovat QR kod a PermaLink. | + | |
- | + | ||
- | + | ||
- | ===== Struktura repozitáře MLABu ===== | + | |
- | + | ||
- | + | ||
- | * Projektová metadata - json | + | |
- | * Commit message - začátek velké písmeno, slova jako added, fixed, removed, started, finished... | + | |
- | + | ||
- | ==== Jmenná konvence ==== | + | |
- | + | ||
- | bez_diakritiky_a_specialnich_znaku_mezery_nahrazeny_podtrzitkem_pouze_mala_pismena_strucne_a_srozumitelne | + | |
- | + | ||
- | + | ||
- | + | ||
- | ==== Adersářová struktura modulu ==== | + | |
- | + | ||
- | MODUL01A/ | + | |
- | hw/ | + | |
- | sch_pcb | + | |
- | gerb_ama | + | |
- | gerb_profi | + | |
- | hdl | + | |
- | cad | + | |
- | sw/ | + | |
- | doc/ | + | |
- | src | + | |
- | img | + | |
- | datasheets | + | |
- | MODUL01A.cs.pdf | + | |
- | MODUL01A.en.pdf | + | |
+ | {{: | ||
+ | ===== Sample construction ===== | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[en: | ||
+ | * [[en: |
en/navody.txt · Last modified: 2023/01/15 12:59 by 94.112.192.193