en:rules
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
en:rules [2019/02/09 15:19] – fluktuacia | en:rules [2019/02/10 14:39] – fluktuacia | ||
---|---|---|---|
Line 264: | Line 264: | ||
Modules’ indicator LEDs can be of SMD or LED 3 mm types. SMD diodes can be placed also on the bottom side of the board that is turned towards the base plate. In such case, it is recommended to design a hole of approximately 1 mm in diameter over the SMD LED, through which the LED will be visible. | Modules’ indicator LEDs can be of SMD or LED 3 mm types. SMD diodes can be placed also on the bottom side of the board that is turned towards the base plate. In such case, it is recommended to design a hole of approximately 1 mm in diameter over the SMD LED, through which the LED will be visible. | ||
- | ===== Text / Printing (?? Potisk) | + | ===== Text / Legend printing |
Modules’ printings should respect a general typographical rules in order for it to be readable even after an application of screen printing. | Modules’ printings should respect a general typographical rules in order for it to be readable even after an application of screen printing. | ||
Line 270: | Line 270: | ||
==== Font ==== | ==== Font ==== | ||
- | One module can accommodate more font sizes (usually less than 3 is necessary). They are used in a following order: name of the module, | + | One module can accommodate more font sizes (usually less than 3 is necessary). They are used in a following order: name of the module, |
=== Alignment === | === Alignment === | ||
- | Same priority signals should have the same font size across the whole module. Size and a style of individual | + | Same priority signals should have the same font size across the whole module. Size and style of individual |
- | Popisky jednotlivých signálů na hřebínku se zarovnávají ke konektoru, aby byla minimalizována možnost řádkové chyby při zapojování. | + | Legend to individual signals on a pin should be aligned to connector in order to minimise a possibility of line error (?? Řádková chubs) when connecting. |
- | === Velikosti Písma | + | === Font Sizes === |
- | Nejčastější používané velikosti písma jsou: | + | Most commonly used font sizes are as follows: |
- | Width 1,5 mm, Height 1,5mm, Thickness 0,3mm - název modulu, důležité informace a popisky hřebínků | + | Width 1.5 mm, Height 1.5mm, Thickness 0.3mm - module name, important information and pins’ legends |
- | Width 1,3 mm, Height 1,3mm, Thickness 0,3mm - popisky jednotlivých vývodů hřebínků | + | Width 1.3 mm, Height 1.3mm, Thickness 0.3mm - legend to an individual pin nails (??) popisky jednotlivých vývodů hřebínků |
- | Velikost písma menší než 1,3 mm je problematická | + | Font sizes smaller than 1.3 mm is problematic and it should only be use when there is a very good reason for it. |
- | Na některých malých modulech může vzniknout problém s délkou názvu modulu, v takovém případě se název modulu zalamuje u verze modulu, například: | + | Some small modules might have a problem with length of their names - in such cases, the module’s name are wrapped to the next line at module version, for example: |
{{: | {{: | ||
- | ISL2902001A | + | ISL2902001A |
- | ==== QR kódy ==== | + | ==== QR codes ==== |
- | Na všechny moduly které jsou dostatečně velké, aby na ně mohl být umístěn | + | |
+ | All sufficiently large modules should have a QR code placed on them. It contains module’s identification and a link to a side with [[http:// | ||
qrencode -s 15 -l L " | qrencode -s 15 -l L " | ||
- | Pokud jste pro vytvoření modulu použili | + | If you have used mlabgen |
<WRAP info round> | <WRAP info round> | ||
- | Vhodnejší by pravděpodobně bylo použití | + | It will probably be better to use [[http:// |
</ | </ | ||
=== PADS === | === PADS === | ||
+ | |||
Miho pro potřeby generování kódu do potisku plošného spoje vytvořil [[http:// | Miho pro potřeby generování kódu do potisku plošného spoje vytvořil [[http:// |
en/rules.txt · Last modified: 2023/02/03 00:14 by kaklik