cs:duckweed_collector
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
Obě strany předchozí revizePředchozí verzeNásledující verze | Předchozí verze | ||
cs:duckweed_collector [2014/08/17 10:00] – kakl | cs:duckweed_collector [Unknown date] (aktuální) – upraveno mimo DokuWiki (Unknown date) 127.0.0.1 | ||
---|---|---|---|
Řádek 1: | Řádek 1: | ||
====== Žabincosběrač I ====== | ====== Žabincosběrač I ====== | ||
- | Loď na uklízení žabince z rybníku. | + | Loď na uklízení žabince z rybníku. Jinak demonstrační konstrukce dálkově řízené lodi s vrtulovým pohonem. |
[[http:// | [[http:// | ||
- | Brushless Motor Controller (ESC) | + | ===== Brushless Motor Controller (ESC) ===== |
- | Thanks for using Turborix (AE) Brushless Motor Controllers. Please read the instructions | + | |
+ | Turborix (AE) Brushless Motor Controllers. Please read the instructions | ||
carefully before you start to use new controllers. | carefully before you start to use new controllers. | ||
The ESCs use higher quality micro processor and more FETs with lower intemal | The ESCs use higher quality micro processor and more FETs with lower intemal | ||
resistance. As such, they outperform many other ESCs. In particular, they have extremely | resistance. As such, they outperform many other ESCs. In particular, they have extremely | ||
performance-cost ratio. | performance-cost ratio. | ||
- | Technical details: | + | |
- | Model Current (A) BEC Cells Weight (g) | + | [[http:// |
- | FM10A 10 Max 1A NiCd/NiMh 6-12 10 | + | ==== Technical details: |
- | Li-Po | + | Model FM10A |
- | FM20A | + | Current |
- | 20 | + | BEC Max 1A |
- | Max 2A | + | Cells NiCd/NiMh 6-12; 2-3 Li-Po |
- | NiCd/NiMh 6-12 | + | Weight 10 (g) |
- | Li-Po | + | |
- | FM30A | + | |
- | 30 | + | |
- | Max 3A | + | |
- | 40 | + | |
- | OPTO | + | |
- | FM60A | + | |
- | 60 | + | |
- | OPTO | + | |
- | FM80A | + | |
- | 80 | + | |
- | OPTO | + | |
- | FM120A | + | |
- | 120 | + | |
- | OPTO | + | |
- | 55 | + | |
- | 3-6 | + | |
- | NiCd/NiMh 8-18 | + | |
- | Li-Po | + | |
- | 55 | + | |
- | 3-6 | + | |
- | NiCd/NiMh 8-18 | + | |
- | Li-Po | + | |
- | 35 | + | |
- | 3-6 | + | |
- | NiCd/NiMh 8-18 | + | |
- | Li-Po | + | |
- | 25 | + | |
- | 2-3 | + | |
- | NiCd/NiMh 8-18 | + | |
- | Li-Po | + | |
- | 18 | + | |
- | 2-3 | + | |
- | NiCd/NiMh 6-12 | + | |
- | Li-Po | + | |
- | FM40A | + | |
- | 2-3 | + | |
- | 78 | + | |
- | 3-6 | + | |
- | Diagram for FM10A, FM20A, FM30A | + | |
- | DC Power | + | |
- | ESC | + | |
- | BEC | + | |
- | Throttle | + | |
- | signal | + | |
- | (Receiver) | + | |
- | Signal from receiver and | + | |
- | provide power to receiver | + | |
- | Diagram For FM40A, FM60A ,FM80A, FM120A | + | |
- | DC Power | + | |
- | ESC | + | |
- | BEC | + | |
- | Throttle signal (Receiver) | + | |
- | Signal from receiver | + | |
- | 5V DC power | + | |
Main functions: | Main functions: | ||
1. Safety mode: the motor won’t start no matter what the position of the control stick is | 1. Safety mode: the motor won’t start no matter what the position of the control stick is | ||
when switched on the RC unit. When the throttle is not at lowest or Max position, it will | when switched on the RC unit. When the throttle is not at lowest or Max position, it will | ||
- | sound by “di-di-di” for warning.2. Brake: On / Off (factory setting is Off). | + | sound by “di-di-di” for warning. |
+ | |||
+ | 2. Brake: On / Off (factory setting is Off). | ||
3. Battery type: NiCd/NiMh, LiPo. | 3. Battery type: NiCd/NiMh, LiPo. | ||
+ | |||
4. Number of batteries: automatic (when setting Battery Type, the ESC will set Number | 4. Number of batteries: automatic (when setting Battery Type, the ESC will set Number | ||
of Batteries automatically at the same time) | of Batteries automatically at the same time) | ||
+ | |||
5. Start up mode: Soft start up, Hard start up | 5. Start up mode: Soft start up, Hard start up | ||
+ | |||
6. Timing mode: Soft timing-for 2, 4, 6 pole brushless motors, Hard timing-for 6 and more | 6. Timing mode: Soft timing-for 2, 4, 6 pole brushless motors, Hard timing-for 6 and more | ||
pole motors, Auto | pole motors, Auto | ||
+ | |||
7. Temperature protection: the controller will reduce output power when temperature | 7. Temperature protection: the controller will reduce output power when temperature | ||
reaches 120 degrees centigrade | reaches 120 degrees centigrade | ||
+ | |||
8. Low voltage protection: reduce output power when the voltage goes down below the | 8. Low voltage protection: reduce output power when the voltage goes down below the | ||
setting (setting of low voltage is 2.8V times number of batteries) | setting (setting of low voltage is 2.8V times number of batteries) | ||
+ | |||
Operating instructions: | Operating instructions: | ||
+ | |||
- Normal start up: | - Normal start up: | ||
+ | |||
Connect the controller and motor as above connection drawing. Switch on the transmitter | Connect the controller and motor as above connection drawing. Switch on the transmitter | ||
and check the throttle stick at lowest position. Connect the main power pack and switch on | and check the throttle stick at lowest position. Connect the main power pack and switch on | ||
Řádek 95: | Řádek 53: | ||
stick is not at lowest position, you will hear “di-di-di”, | stick is not at lowest position, you will hear “di-di-di”, | ||
lowest position. | lowest position. | ||
+ | |||
- Set up by Throttle Stick: | - Set up by Throttle Stick: | ||
Connect controller with motor as above connection diagram. Switch on the transmitter and | Connect controller with motor as above connection diagram. Switch on the transmitter and | ||
Řádek 104: | Řádek 63: | ||
above steps for other settings. After your setting, keep the stick at lowest position for 5 | above steps for other settings. After your setting, keep the stick at lowest position for 5 | ||
seconds, you will hear a piece of music. Now, you can begin flying. | seconds, you will hear a piece of music. Now, you can begin flying. | ||
+ | |||
Prompting Sound: | Prompting Sound: | ||
+ | |||
1. Brake On: - - - | 1. Brake On: - - - | ||
+ | |||
2. Brake Off: - - - - - - | 2. Brake Off: - - - - - - | ||
+ | |||
3. NiCd / NiMh: . - . - . - | 3. NiCd / NiMh: . - . - . - | ||
+ | |||
4. LiPo: . -- . -- . – | 4. LiPo: . -- . -- . – | ||
+ | |||
5. Soft Start up: .. - .. - .. – | 5. Soft Start up: .. - .. - .. – | ||
+ | |||
6. Hard Start up: .. -- .. -- .. – | 6. Hard Start up: .. -- .. -- .. – | ||
+ | |||
7. Soft Timing: ... “ ...” ...” | 7. Soft Timing: ... “ ...” ...” | ||
+ | |||
8. Hard Timing: ,,, -- ,,, -- ,,, -- | 8. Hard Timing: ,,, -- ,,, -- ,,, -- | ||
+ | |||
9. Reset to Factory Setting: ... ... ... | 9. Reset to Factory Setting: ... ... ... | ||
+ | |||
The controllers are supplied with factory setting, Brake Off, Soft start up and Auto timing. | The controllers are supplied with factory setting, Brake Off, Soft start up and Auto timing. | ||
Note: when the first time of using the ESC, or when changing number of batteries, | Note: when the first time of using the ESC, or when changing number of batteries, | ||
or when changing battery type, the setting of Battery Type must be done every time. | or when changing battery type, the setting of Battery Type must be done every time. | ||
- | Programming Card: | + | |
- | Turborix (AE) ESC can be programmed by a E-PRG-1 programming card. It will expand | + | |
- | ESC’s functions and suitability. Details please see the instructions of E-PRG-1 | + | ==== TODO ==== |
- | Programming Card.Notice: | + | |
- | 1. Every Turborix (AE) ESC of FM10A, FM20A and FM30a has a BEC plug (JR | + | === Dálkové ovládání === |
- | connector), it is for connecting to receiver and also for connecting to Programming | + | |
- | Card. For FM40A, FM60A, FM80A and FM120A there are two JR connectors on each | + | * Nahradit mechanický křížový ovladač magnetickým joystickem tisknutelným na 3D tiskárně. |
- | ESC. The one with long wire is for connecting to receiver. The one with short wire is | + | * Zvážit nahrazení ovladače smartphonem. |
- | for connecting to Programming Card. | + | * Použít modul [[cs:ant]] |
- | 2. Choose suitable brushless motors and propellers, ensure the working current never | + | |
- | exceed specified current of ESC. | + | === Loď === |
- | 3. Make sure the connecting for battery positive and negative is right. Reversing the | + | |
- | connection will damage the ESC permanently. | + | * Vyřešit vícečlánkové napájení modulem [[cs:lion2cell]] |
- | 4. Use suitable batteries, do not exceed specified voltage of ESC. | + | * Zatáčení kormidlem na servu nahradit dvěma dmychadly s krytými vrtulemi. |
- | 5. Do not disassemble the ESC by self, it will damage the ESC or lose message. | + | * Upravit konstrukci jako nosnou pro ponorku. |
- | 6. The ESCs are designed for airplane models only. | + | |
- | 7. Take care in using safely. Incorrect use may cause injury to the body. The company | + | |
- | will not be responsible for any damage or loss caused by incorrect operation. | + | |
- | 8. Reverse the motor direction by exchanging the position of any two connections to the | + | |
- | motor. | + | |
- | Warning: | + | |
- | The propellers on turning are dangerous. Disconnect the main power | + | |
- | pack immediately after flying. | + | |
- | Turborix (AE) keeps the rights to change design, function or package, | + | |
- | without notice. | + |
cs/duckweed_collector.txt · Poslední úprava: 2014/08/31 21:15 (upraveno mimo DokuWiki)